Dielectric relaxation analysis of starch oligomers and polymers with respect to their chain length

Starch belongs to the polyglucan group. This type of polysaccharide shows a broad β-relaxation process in dielectric spectra at low temperatures, which has its molecular origin in orientational motions of sugar rings via glucosidic linkages. This chain dynamic was investigated for α(1,4)-linked starch oligomers with well-defined chain lengths of 2, 3, 4, 6, and 7 anhydroglucose units (AGUs) and for α(1,4)-polyglucans with average degrees of polymerization of 5, 10, 56, 70, and so forth (up to 3000; calculated from the mean molecular weight). The activation energy (E_a) of the segmental chain motion was lowest for dimeric maltose (E_a = 49.4 ± 1.3 kJ/mol), and this was followed by passage through a maximum at a degree of polymerization of 6 (E_a = 60.8 ± 1.8 kJ/mol). Subsequently, E_a leveled off at a value of about 52 ± 1.5 kJ/mol for chains containing more than 100 repeating units. The results were compared with the values of cellulose-like oligomers and polymers bearing a β(1,4)-linkage. Interestingly, the shape of the E_a dependency on the chain length of the molecules was qualitatively the same for both systems, whereas quantitatively the starch-like substances generally showed higher E_a values. Additionally, and for comparison, three cyclodextrins were measured by dielectric relaxation spectroscopy. The ringlike molecules, with 6, 7, and 8 α(1,4)-linked AGUs, showed moderately different types of dielectric spectra. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 188–197, 2004     

Effect of hardness and composition gradients on Barkhausen emission in case hardened steel

The effect of gradients in hardness, structure and composition in the surface layers on magnetic Barkhausen noise (MBN) was investigated in two widely used low alloy steels. One material was case hardened by induction hardening. The other was case carburised. Similar hardness profiles were produced by the two treatments. It was found that the variation in structure and hardness through the case in the induction-hardened steel had a minor effect on the MBN profile. In contrast, the inhomogeneity in the case-carburised material showed up clearly. This took the form of a broadened or two-peak MBN profile. When the surface layer containing the case was removed by etching, the broadened profile was replaced by a profile with a single peak. It is concluded that the shape and position of the MBN profile is significantly affected when a gradient in microstructure is induced by a gradient in carbon content. On the other hand, a gradient in microstructure induced by heat treatment with a constant carbon level has much less affect on the MBN profile for the induction-hardened steel.     

锡(Ⅳ)-偶氮邻苯二酚苯基荧光酮-吐温-80体系分光光度法测定岩石中微量锡

pH值在7.0-8.5的范围内，锡与偶氮邻苯二酚苯基荧光酮、吐温－80形成络合物，其最大吸收峰556nm，摩尔吸光系数2.9×10^5L·mol^-1·cm^-1，锡的含量在0－6μg/25mL范围内遵守比耳定律，本方法对干扰离子的影响和消除进行了研究，本方法已被用于岩石样中锡的测定，结果满意。     

Effects of the architecture and environment on polymeric molecular assemblies of novel amphiphilic diblock copolynorbornenes with narrow polydispersity via living ring‐opening metathesis polymerization

Diblock copolymers of 5‐(methylphthalimide)bicyclo[2.2.1]hept‐2‐ene (NBMPI) and 1,5‐cyclooctadiene were synthesized by living ring‐opening metathesis polymerization with a well‐defined catalyst {RuCl₂(CHPh)[P(C₆H₁₁)₃]₂}. Unhydrogenated diblock copolymers showed two glass transitions due to poly(NBMPI) and polybutadiene segments, such as two glass‐transition temperatures at ?86.5 and 115.3 °C for poly 1a and ?87.2 and 115.3 °C for poly 1b . However, only one melting temperature could be observed for hydrogenated copolymers, such as 119.8 °C for poly 2a and 121.7 °C for poly 2b . The unhydrogenated diblock copolymer with the longer poly(NBMPI) chain (poly 1a ; temperature at 10% mass loss = 400 °C) exhibited better thermal stability than the one with the shorter poly(NBMPI) chain (poly 1b ; temperature at 10% mass loss = 385 °C). Two kinds of hydrogenated diblock copolymers, poly 2a and poly 2b , exhibited relatively poor solubility but better thermal stability than unhydrogenated diblock copolymers because of the polyethylene segments. Poly[(hydrochloride quaternized 2‐norbornene‐5‐methyleneamine)‐b‐butadiene]‐1 (poly 3a ) was obtained after the hydrolysis and quaternization of poly 1a . Dynamic light scattering measurements indicated that the hydrodynamic diameters of the cationic copolymer (poly 3a ) in water (hydrodynamic diameter = 1580 nm without salt), methanol/water (4/96 v/v; hydrodynamic diameter = 1500 nm without salt), and tetrahydrofuran/water (4/96 v/v; hydrodynamic diameter = 1200 nm without salt) decreased with increasing salt (NaCl) concentration. The effect of temperature on the hydrodynamic diameter of hydrophobically modified poly 3a was also studied. The inflection point of the hydrodynamic diameter of poly 3a was observed at various polymer concentrations around 30 °C. The critical micelle concentration of hydrophobically modified poly 3a was observed at 0.018 g dL^?1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2901–2911, 2006     

Influence of chemistry and hot rolling conditions on high permeability non-grain oriented silicon steel

This paper discusses the influence of chemical composition on the final electromagnetic properties in higher permeability material. Furthermore, the effect of the hot rolling practice and the end of austenite transformation temperature range on the hot band microstructure is described. The magnetic polarization J₅₀₀₀ better than 1.7 T, using hot rolling conditions 40 mm transfer bar thickness, finish mill entry temperature 1000 °C, and finishing temperature 800–840 °C and after decarburization heat treatment and grain growth treatment, was obtained.     

Optogalvanic spectra of calcium in the 6090–6760 Å region

Optogalvanic spectra of some 30 transitions of calcium originating from the ground state as well as from several excited states (4s4p ^1,3P, 4s3d ^1,3D, 4s5p ³P, 3d4p ³D, ³F) have been investigated using laser-irradiation of a low-current glow discharge in a thermionic diode. The influence of various experimental parameters such as bias field, oven temperature and buffer gas pressure on the spectra are reported. Seven previously unreported transitions are recorded including four forbidden transitions which violate the J selection rules. An interesting anomaly observed in the non-statistical population of the 4s3d ³D_3,2,1 multiplet is discussed where the populations of ³D₃:³D₂:³D₁ are in the ratio of 94:5:1. A possible explanation is based on avoided crossing between potential energy curves of the Ca-Ar molecule.     

Dynamic electrochemical impedance spectroscopy measurements of passive layer cracking under static tensile stresses

Electrochemical impedance spectroscopy allows the examination of corrosion susceptibility and resistance for different construction materials, in particular the determination of the properties of their passive films. This technique makes possible the analysis of electrochemical processes in time domain, including rapid phenomena such as changes in the properties of passive films, but it has never been used for passive layer cracking examination. In many cases, fracture of the passive film under tensile stresses leads to stress corrosion cracking. Therefore, investigations of passive layer cracking on austenitic stainless steels under tensile stresses facilitate the understanding of the mechanism of stress corrosion cracking in these common engineering materials. The effect of static tensile stresses on the passive film cracking behaviour of type 304L stainless steel immersed in 0.5 M NaCl solution at room temperature has been investigated. This paper presents the impedance spectra obtained for 304L stainless steel samples at different potential values.Contribution to the 3rd Baltic Conference on Electrochemistry, Gdansk-Sobieszewo, Poland, 23–26 April 2003Dedicated to the memory of Harry B. Mark, Jr. (28 February 1934–3 March 2003)     

Die Isolierung radioaktiv markierter nichtmetallischer Einschlüsse aus Hochlegierten Stählen

Zur Isolierung von Einshlüssen aus hochlegierten Stählen werden die Hauptkomponenten Fe, Ni, Cr und weitere Metalle durch mehrstufig ausgeführte Flüssig-Flüssig-Extraktionen mit verschiedenen Extraktionsmitteln abgetrennt. Die im Eindampfrückstand der wäβrigen Phase nach der Extraktion verbleibenden Einschlüsse können für die meisten Radionuklide ohne nennenswerte Selbstabsorption mit einem Groβflächenzählrohr oder anderen geeignetenZählvorrichtungen ausgemessen werden.     

Monitoring of the shrinkage during the photopolymerization of acrylates using hyphenated photorheometry/near‐infrared spectroscopy

This article describes a new method for the quantitative determination and time‐resolved monitoring of the polymerization shrinkage during ultraviolet (UV) photopolymerization. It is based on rheometry using a modified oscillating rheometer. Shrinkage is determined from the decrease of the gap between the rheometer plates. Moreover, near‐infrared (NIR) spectra can be recorded directly in the rheometer, which allows continuous determination of the conversion at any time of a shrinkage measurement. As both shrinkage and conversion data come from the same experiment, shrinkage can be analyzed in dependence on the current conversion achieved during UV irradiation, which enables direct investigation of correlations between both parameters. Hyphenated photorheometry/FT‐NIR spectroscopy was used for the determination of the polymerization shrinkage of pure acrylate monomers and oligomers as well as acrylate‐based formulations. Quantitative shrinkage values were found to be in excellent correlation with data that were determined by an independent method (via buoyancy measurements) and data from literature. Furthermore, the effect of ambient and irradiation conditions or the content of nanoparticles on the degree of shrinkage was studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 729–739     

Enhanced spin capturing polymerization: Numerical investigation of mechanism

Simulation on the kinetic scheme of enhanced spin capturing polymerizations (ESCP) were performed to reveal the influence of different parameters, e.g., initiation rate, spin capturing and side reactions on the properties (the monomer conversion, degree of polymerization, polydispersity index, and the fraction of “living” chains) of polymer obtained. The kinetic scheme of ESCP was solved numerically as well as the method of statistical moments of molecular weight distribution was applied to get some numerical expressions for analysis. The simulations showed that fast initiation rate can lead to decrease of living fraction and broadening of molecular weight distribution. Whereas high rate of spin capturing makes the polymer chains shorter but increases living character. And side reactions always decrease livingness of the polymer obtained. Finally in the case of absence of side reaction we were able to formulate criteria for formation of polymer with target molecular weight and quota of living chains via ESCP process. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2546–2556